Performance Supply Co.
My Account
About Us
Contact
DrawStraw™
Big Line Kits
VPMAX Filter Systems
VPMAX Intercooler Boot Kits
Products
Fuel Systems, Big Line Kits
Fuel Pressure Regulators
VP Max Filter Systems
Fuel Systems
Fuel Pressure Regulators
Replacement Pumps
AirDog & Raptor
Other fuel system upgrades
Fuel Filtration
DrawStraw™ Fuel Module Upgrades
Big Line kits
Injection Pumps
Filters, Filter Kits
AirDog Parts & Accessories
AirDog - Raptor Parts
DrawStraws™
Fuel Line
Filters
Fittings, Adapters, Fuel Line, Harnesses
Schrader Valves
Metric Adapters
JIC/AN adapters
Other JIC Fittings
NPT Fittings
Pushlock Fittings
Clamps
ORB Fittings
Barb Fittings
Banjo Fittings
Misc Fittings
Quick Connect
Seals & O-Rings
Specialty Fittings
Harnesses
Fuel Line
Electrical Parts
VPMAX Intercooler Boot Kits
Dodge Cummins
Ford Powerstroke
Replacement Filters
Fuel Filters
Turbo Hoses & Clamps
Silicone Hoses
V Band Clamps
Flat Band Clamps
Gauge Accessories
Helpful Links
Links
Info & Technical Help
Join our mailing list!
Home
>
Fuel Systems, Big Line Kits
>
Fuel Systems
>
Other fuel system upgrades
>
Modified Fuel Module 98-04 Diesel Dodge Ram
Note:
Please read below before ordering.
VPMAX
MFM2 Modified Fuel Module 98-04 with
DrawStraw 5
installed.
For 98-04 trucks only.
All units come with a 1/2" J2044 Male Quick Connect for the suction line
and a 1/2" Female Pushlock adapter connection for your hose.
as shown in the picture.
Pump and related components are removed and our components installed.
These have new fuel level senders in them.
Units do not have a filter.
Comes with a rubber tank gasket.
The original 5/16 and 3/8 QC module ports are intact. The 5/16 for your injection pump return and the 3/8 port may be used for your AirDog II return or other pumps with low return volume.
*
Pumps with a high volume return should follow the pump manufacturers recommendation for installation. Failure to do so could result in changes in fuel pressure.
Note:
Please read below before ordering.
For 98-04 trucks with stock connections only.
NOTE:
Units must be tested BEFORE installation to ascertain if any damage may have occurred in transit to avoid installing a potentially damaged unit.
NOTE:
The resistor board assemblies on fuel modules are fragile, care should be taken not to drop the module or put unnecessary pressure on the float arm or the resistor board unit. Boards can crack and not be easily visible to the naked eye.
Fuel level sensors are tested before they are packaged for shipment at our location. It's necessary they be tested by the installer just prior to installation to be certain no damage occurred while in transit.
Using an OHM meter connect leads to the two center pins on the plug. There should be an approximate 180-200 Ohm spread from low to high.
Note: These vented units are equipped with roll over valves,
do not overfill tank.
Module comes as shown with no other accessories.
For 98-04 Dodge Ram only
,
fuel gauge will not read properly
if used on pre 1998 applications
,
Be certain to read this page thoroughly before ordering as there are
NO returns on fuel modules.
This unit does not have a pump inside.
Our Price:
$
269.99
Availability::
Usually Ships in 2 to 3 Business Days
Part Number (P/N):
MFM2
Qty:
Description
MFM2 (6)
18x8x8 5lb Dim 11lb
Related Products...
Push Lock Fuel Pressure Tee 3/8"
Our Price:
$12.00
Add
P Pump Dual Feed Hose
Our Price:
$79.99
Add
Pump Relocation Kit 3/8
Our Price:
$150.00
Add
Tapped Banjo Bolt
Our Price:
$12.00
Add
Return Bulkhead Assembly
Our Price:
$37.00
Add
Browse for more products in the same category as this item:
Fuel Systems, Big Line Kits
>
Fuel Systems
>
Other fuel system upgrades
Fuel Systems, Big Line Kits
>
DrawStraw™ Fuel Module Upgrades
Fuel Systems, Big Line Kits
>
Fuel Systems
Fuel Systems, Big Line Kits